1 - Indoor coil inspection

2 - Condenser coil inspection

3 - Electrical inspection: we’ll check for exposed or loose wires that could destroy the air conditioner or worse, cause a fire in your home.

4 - Capacitor inspection and testing

5 - Fan blade inspection

6 - Service valve inspection: if this is malfunctioning, your unit will not emit the right amount of refrigerant, resulting in an air conditioner that doesn’t properly cool down your home

7 - Safety device inspection: a properly working safety device means that the unit will shut off if it is malfunctioning, saving you from dangerous situations

8 - Duct work inspection

9 - Bearing inspection and lubrication

10 - Blower Motor inspection: we’ll check the amperage and voltage, check for cracks, and lubricate the motor belt

11 - Air filter cleaning and/or replacement: we recommend that you have the filter changed every 3 months or more for maximum efficiency

12 - Condensate drain inspection: we’ll check for clogs and algae build-up that could cause odors and higher humidity in your home

13 - Refrigerant inspection. The techinican could check the level of refrigerant and determine if needs to be recharged. The technician may add only up to 6 oz as part of the service if required. Each additional recharge of refrigerant has an additional cost per lb after the first 6 oz

14 - Electrical disconnect box inspection

15 -Check and inspect switches

16 - Outdoor Condenser coil cleaning: any amount of dirt or dust blocking the fins on the outside of the unit can prevent airflow and reduce your air conditioner’s efficiency

17 - Check and clean A/C outdoor unit

18 - Supply/Return temperature differential inspection

19 - Compressor inspection and maintenance: as the heart and soul of your air conditioner, it’s critical that the compressor is in full working order

20 - Debris removal: this ensures that your unit is working at maximum efficiency and free of fire hazards. Contractor Licensed 1053819.

1 - Ductwork inspection.

2 - Check for exposed wires.

3 - Check for leaks or moisture.

4 - Check for excessive wear and tear.

5 - Complete lubrication of all moving parts.

6 - Check pilot light.

7 - Check gas pressure.

8 - Air filter clean and/or replacement.

9 - Check and clean blower.

10 - Check and tighten electrical connections.

11 - Inspect flue pipe

12 - Check amperage to blower

13 - Inspect heat exchanger

14 - Cycle the furnace.

15 - Check and calibrate thermostat.

16 - Check for gas leaks.

17 - Check ignition protocols.

18 - Clean outside surface of unit.

19 - Ensure unit is in compliance with manufacturer recommendations.

20 - Written report Contractor Licensed 1053819.

1 - We clean the register covers to remove cooking oil film,nicotine film and other dust-collecting substances.

2 - The air ducts are then brush vacuumed clean with our exclusive,patented ROTOBRUSH. The ROTOBRUSH removes the contaminants that circu- late through the air duct system. We will sanitize your air ducts and vents with an environmental Envirocon safe sanitizer commonly used in hospitals and nursing homes,leaving behind a fresh scent.**sanitizer additional cost**

3 - We deep clean the source of the air supply including (where applicable) the blower,squirrel cage,coils,con- densation pan and return air supply.**additional cost**

4 - Air Duct Sanitizer-Disinfecting (Envirocon) . We use a product called envirocon. It is a disinfectant as well as a deodorizer that kills bacteria, viruses, fungus, mold, and mildew, in addition to eliminating odors. A Sporicidin treatment will inhibit the accumulation and growth of any contaminants. It is a non-toxic product approved and certified for EPA. (Envirocon) **aditional cost**

5 - Roto-Vision inspected and recording to show you where the trouble spots are, and verifies the job was done right!. **additional cost**

*Our Web-site is here: https://www.cycloneairsystems.com. Cyclone Air Systems Inc. Call Now 1-888-870-1166